Get A Quote

 

 

Everybody seems to have their private rationale with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall surface to remove the old tub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the new one. See to it you have certified yourself for the task and fit attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need a professional plumber to make tube links.
This write-up will certainly help you set up a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not need to transform the arrangement of your previous water pipes.
Your devices and product checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Setup

To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.

 

 

Removing Old Taps

If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Tub

Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub till the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water system and also examine all joints and new pipework for leaks as well as tighten them if needed. Load the tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the tub has actually been utilized a minimum of once as this will certainly resolve it right into its final position.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the tap and the sink. Secure the tap in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former kind must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I ran across that review on Tools You Need to Install a New Bathtub while doing a search on the web. Liked our piece? Please share it. Help other people locate it. Many thanks for your time invested reading it.

Visit Link